Loading... Please wait...

security banner

Our Newsletter

Rowing Action Manual Drum Pump

  • Alemlube 5005AN Rowing Action Manual Drum Pump
$424.60 (inc GST) $386.00 (exc GST)
15.00 KGS
Freight charges dependent on destination & quoted after receipt of order. We will source most competitive freight charges for you. Item freight costs to be paid by customer prior to dispatch.
Calculated at checkout

$424.60 (inc GST) $386.00 (exc GST)">

Rowing Action Drum Pump.

The Alemlube 5005AN2 manual drum pump is designed for the transfer of fuels and lubricants up to SAE30. This economical and hard working drum pump has a delivery rate of approximately 1 litre per stroke or approximately 40 litres per minute. Lightweight, the pump is supplied with 2.4 metres of delivery hose, a versatile metal delivery spout and a spout holster. The simple and proven design of the 5005AN2 makes this pump the ideal drum pump for fuel and lubricant transfer in challenging and harsh operating environments.



Use: Petrol, diesel, kerosene and lubricants up to SAE30. 60 or 205 litre drums
Discharge Volume: 40 litres per minute or 1 litre per stroke
Inlet/Outlet Inlet: 1”BSP Outlet: 1”BSP
Hose: 2.4 metres of 1”ID fuel resistant hose
Materials: Aluminium handle, aluminium body with POM piston and piston rings






Fitting the telescopic downtube to the pump

Screw the downtube to the pump, carefully applying the thread tape to the thread on the downtube to ensure there are no air leaks between the downtube and the pump inlet whilst securing the downtube firmly in place.

Fitting the pump to the drum or tank

  1. Pull out the short tube to the fully extended position then place the pump in the drum or tank.
  2. Screw the pump to the drum or tank firmly.

Fitting the hose to the pump (Sequence Is Important)

  1. Place the hose & spout in the hose holster. (The locking pin on the spout engages in the keyway at the extreme left of the holsters opening).
  2. Turn the spout fully clockwise to ensure that when fully assembled, the nozzle locking pin rests vertically within the holster.
  3. Fit the hose clamp loosely to the end of the hose and slide the spring down onto the hose.
  4. Push the hose end onto the pump outlet, slide the hose clamp over the hose at the outlet and tighten. Slide the hose spring up against the hose clamp. Check that the spout locking pin is still in a vertical position inside the holster. If not, adjust the hose position on the spout to correct this.

Pump Operation

When the handle is pulled back, the piston is pushed up by the con rod and the valve closes. At the same time fuel or lubricant on the top of the piston is discharged through the hose. When the handle is pushed forward, the piston is pulled down by the cross bar and the valve is opened. The fuel or lubricant then flows past the valve through the centre of the piston and fills the cylinder above the piston. The inlet valve is closed during this stroke.


Warranty Information

Your Alemlube product is warranted to the original user against defects in workmanship or materials under normal use for a period of twenty four months* after purchase date. Any products which is determined to be defective in material and workmanship and returned to Alemlube P/L, shipping costs prepaid, will be repaired or replaced at Alemlube’s option.
This warranty also covers parts that are subject to wear such as O rings, packings, seals, springs, electronic and even electrical components.
The warranty does not cover damage or failure which in the judgement od Alemlube arises from misuse, abrasion, corrosion, negligence, accidental damage, faulty installation or tampering. If Alemlube inspection discloses no defect in material or workmanship, repair or replacement and return will be made at customary charges.

*Applies to the vast majority of Alemlube products.

Find Similar Products by Category

You Recently Viewed...